| Package Photo |
Product Series
 |
Supply
Voltage |
Freq. min.(MHz) |
Freq. max.(MHz) |
No. of pins or pads |
Package Size (mm) / Description / Features |
 |
3HPL5761 |
3.3 V |
0.75 |
800 |
6 |
5x72.5, Tri-state on pad 1. PLL based, 6 pad SMD. Low cost. Moderate phase noise. -125 dBc/Hz at 10 KHz offset for 155.520 MHz. |
| 3HPL5762 |
3.3 V |
0.75 |
800 |
6 |
5x72.5, Tri-state on pad 2. PLL based, 6 pad SMD. Low cost. Moderate phase noise. -125 dBc/Hz at 10 KHz offset for 155.520 MHz. |
 |
3HPL14 |
3.3 V |
0.75 |
800 |
4 |
Full Size 4 pin DIP. PLL based, 6 pad SMD. Low cost. Moderate phase noise. -125 dBc/Hz at 10 KHz offset for 155.520 MHz.
|
 |
3HPL24 |
3.3 V |
0.75 |
800 |
4 |
Full Size 4 pin Gull Wing SMD. PLL based, 6 pad SMD. Low cost. Moderate phase noise. -125 dBc/Hz at 10 KHz offset for 155.520 MHz. |
 |
3HPL8 |
3.3 V |
0.75 |
800 |
4 |
Half Size 4 pin DIP. PLL based, 6 pad SMD. Low cost. Moderate phase noise. -125 dBc/Hz at 10 KHz offset for 155.520 MHz. |
 |
3HPL18 |
3.3 V |
0.75 |
800 |
4 |
Half Size 4 pin Gull Wing SMD. PLL based, 6 pad SMD. Low cost. Moderate phase noise. -125 dBc/Hz at 10 KHz offset for 155.520 MHz. |
 |
3HPL62 |
3.3 V |
0.75 |
800 |
6 |
9.6x11.4x2.5 mm 6 pad FR4 SMD. PLL based, 6 pad SMD. Low cost. Moderate phase noise. -125 dBc/Hz at 10 KHz offset for 155.520 MHz. |
 |
3HPL64 |
3.3 V |
0.75 |
800 |
6 |
9.6x11.4x4.7 mm 6 pad FR4 SMD. PLL based, 6 pad SMD. Low cost. Moderate phase noise. -125 dBc/Hz at 10 KHz offset for 155.520 MHz. |
| Mercury Model |
HPL |
Frequency Range
(package dependent) |
750 KHz ~ 800 MHz. PLL-based. |
| Output Logic |
Differential PECL 100K Square Wave |
Frequency Stability (1)
Commercial (0°C to +70°C)
Temperature Code is "C"
Industrial (-40°C to +85°C)
Temperature Code is "I" |
Stability Code "A": ±25 ppm over 0°C to +70°C
Stability Code "B": ±50 ppm over 0°C to +70°C
Stability Code "C": ±100 ppm over 0°C to +70°C
If non-standard please enter the desired stability after the "C"
(e.g. C20 represents ±20 ppm over 0°C to +70°C) |
Stability Code "D": ±25 ppm over -40°C to +85°C
Stability Code "E": ±50 ppm over -40°C to +85°C
Stability Code "F": ±100 ppm over -40°C to +85°C
If non-standard please enter the desired stability after the "I"
(e.g. I20 represents ±20 ppm over -40°C to +85°C) |
vs ±10% Supply Voltage Change: ±3 ppm max.
vs ±10% Load Change: ±2 ppm max. |
| Supply Voltage (VDD) |
3.3 V ± 10% |
| Output Voltage HIGH "1" VOH |
VDD-1.025 V min.; VDD-0.880 V max. Condition: RL= 50 Ω to VDD-2V |
| Output Voltage LOW "0" VOL |
VDD-1.810 V min.; VDD-1.620 V max. Condition: RL= 50 Ω to VDD-2V |
| Current Consumption (typical) |
Fout < 24 MHz: 25 mA
24 MHz < Fout < 96 MHz: 65 mA max.
Fout > 96 MHz: 100 mA
|
| Load |
50 Ω into VDD or Thevenin Equivalent.
(terminating resistors required on all outputs) |
| Rise Time (TR) |
0.6 nano sec. typical; 1.5 nano sec. max (20% ? 80%) |
| Fall Time (TF) |
0.5 nano sec. typical; 1.5 nano sec. max (80% ? 20%) |
| Duty Cycle |
50% ?5% max. measured at VDD -1.3V |
Phase Jitter (RMS)
(12 KHz to 20 MHz) |
2.6 ps typical; 4 ps max. for 155.520 MHz
2.5 ps typical; 4 ps max. for 622.080 MHz |
| Phase Noise (RMS) typical |
19.440 MHz |
77.760 MHz |
106.250 MHz |
155.520 MHz |
622.080 MHz |
| 2.1 ps |
3.5 ps |
4.1 ps |
4.3 ps |
6.0 ps |
| Phase Noise (Peak-to-Peak) |
17 ps |
30 ps |
28 ps |
27 ps |
40 ps |
Phase Noise
(offset from carrier) |
10 Hz Offset |
-80 dBc/Hz |
-75 dBc/Hz |
-70 dBc/Hz |
-60 dBc/Hz |
-50 dBc/Hz |
| 100 Hz Offset |
-108 dBc/Hz |
-100 dBc/Hz |
-98 dBc/Hz |
-90 dBc/Hz |
-77 dBc/Hz |
| 1 KHz Offset |
-132 dBc/Hz |
-125 dBc/Hz |
-122 dBc/Hz |
-115 dBc/Hz |
-102 dBc/Hz |
| 10 KHz Offset |
-142 dBc/Hz |
-132 dBc/Hz |
-123 dBc/Hz |
-125 dBc/Hz |
-115 dBc/Hz |
| 100 KHz Offset |
-142 dBc/Hz |
-130 dBc/Hz |
-117 dBc/Hz |
-119 dBc/Hz |
-108 dBc/Hz |
| Start-up Time |
10 m sec. max. |
| Aging |
±2 ppm per year max. |
| Tristate Option on Pad No. 1 |
No Connection |
PECL and complimentary PECL outputs. |
| Disable |
Both outputs are disabled (high impedance) when pad No. 1 is taken below 0.3 Vcc referenced to ground. Oscillator is always ON.
Special request: Oscillator is off when disabled. Contact Mercury. |
| Enable |
At disabled mode, both outputs are enabled when pad No. 1 is taken above 0.7 Vcc referenced to ground. |
| Input Static Discharge Protection |
2 KV max. |
|
Absolute Maximum Rating (permanent damage may be created if operate beyond limits specified.
|
| Supply Voltage VDD |
+4.6 V D.C. max. |
| Input Voltage Vi |
Vss-0.5 min.; VDD + 0.5V max. |
| Input Voltage Vo |
Vss-0.5 min.; VDD + 0.5V max. |
| Storage Temperature TS |
-55°C min.; +150°C max. |
(1)Inclusive of 25°C tolerance, operating temperature range, ±10% input voltage variation, load change, aging, shock and vibration.
